ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.
|Published (Last):||7 March 2011|
|PDF File Size:||12.4 Mb|
|ePub File Size:||14.54 Mb|
|Price:||Free* [*Free Regsitration Required]|
Materials and Manufacture 5. The base metal shall conform to the chemical requirements of the speci? Several of those considered suitable for use with this speci? Historical Version s – view previous versions of standard Translated Version s: If spectrometric procedures are used, the sample shall be exposed on the center line of the cladding when there is sufficient cladding thickness available so that there is no contamination from the adjacent base metal.
Testing for shear strength for clad plates with minimum cladding thickness of 0. Last previous edition approved in as A — If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Number of Tests and Retests 8.
Aztm of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance. NOTE 2—Punch marks for measuring elongation after fracture shall be made on the?
NOTE 3—The dimension t is the thickness of the test specimen as provided for in the applicable material speci? The nickel or nickel-base alloy cladding metal shall conform to prescribed chemical composition.
The sides of the bend test specimen used for bond strength determination may have the corners rounded to a radius not over 1? This standard has been approved for use by agencies of the Department of Defense.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Specify whether applicable to the cladding alloy, backing steel, or both see Section A number in parentheses indicates the year of last reapproval.
ASTM A265 GR 1 titanium alloy strip sheet plate
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? If the requirements of this speci?
Ultrasonic Examination in accordance with Speci? The minimum cladding thickness for shear testing shall be 0. Workmanship Finish, and Appearance Each specimen shall be in the? The material adtm generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance. This abstract is a brief summary of the referenced standard.
Other tests may be performed by agreement between the supplier and the purchaser. Gage Length cladding and the base steel shall be machined so as to maintain the same ratio of clad metal to base steel as is maintained in the plate, except that the thickness of the clad material need not be reduced below 1?
General Requirements for Delivery Areas within 1 in. A list of standardized supplementary requirements for use at the option of the purchaser are included in Speci?
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. If wet chemical procedures are used, millings may be taken only when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination from the adjacent layer.
The tensile properties thus determined shall meet the base steel requirements.
ASTM A – 12 Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate
Current edition approved May 1, The steel shall be made by the open-hearth, electric furnace with separate degassing and refining optionalor basic-oxygen processes, or by secondary processes whereby steel made from these primary processes is remelted using, but not limited to electroslag remelting or vacuum arc remelting processes.
In reducing z265 thickness of the specimen, both the alloy 3 Metric Equivalents in. The composite plate shall undergo shear strength test, bond strength test, and tension test and shall conform to the required tensile strength and yield strength.
This specification covers the standard for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of nickel or nickel-base alloy.
The base metal shall be carbon steel or low-alloy steel conforming to the specifications for steels for either pressure vessels or for general structural applications. Originally approved in