ASTM A860 PDF

ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: + ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. Manufacturer of Carbon steel WPHY 60 pipe fittings, Exporter of a comprehensive range of products like CS ASTM A elbow, Reducer, Effortless ordering and.

Author: Togar Zulkinos
Country: Togo
Language: English (Spanish)
Genre: Medical
Published (Last): 5 December 2007
Pages: 443
PDF File Size: 15.18 Mb
ePub File Size: 9.28 Mb
ISBN: 169-1-95492-399-5
Downloads: 91037
Price: Free* [*Free Regsitration Required]
Uploader: Gardashura

Originally approved in JIS G Carbon steel pipes for pressure service. Wrought austenitic and austenitic-ferritic duplex asym steels without specific inspection requirements BS EN Butt-welding pipe fittings Part 4: Fittings formed above the transformation temperature or upon which welding is performed, shall be cooled to below the lower critical temperature prior to heat treatment. This abstract is a brief summary of the referenced standard.

This specification does not require hydrostatic testing. If you feel that your comments have not received a fair hearing you should make your views aztm to the ASTM Committee on Standards, at the address shown below. The nickel content of the deposited weld metal shall not exceed 1. NOTE 1—For purposes of identi?

How can I help you? The bar coding system, if zstm at the discretion of the supplier, should be consistent with one of the published industry standards for bar coding. Materials shall be heat treated by normalizing, quenching, atsm tempering or stress relieving.

The purchaser may specify in the order a speci? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

  HAYDEN WHITE EL TEXTO HISTORICO COMO ARTEFACTO LITERARIO PDF

A860 WPHY 65 PIPE FITTTINGS

The chemical composition thus determined shall conform to Table 1. One or more of the supplementary requirements may be specified in the order. Research use only,Commercial use is prohibited. The product analysis shall be the basis for rejection.

After the removal of any atm, the tees shall be re-examined by the original method. A chemical analysis shall be performed on deposited weld metal for aatm heat of? The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Cvenergy absorptionC; measured at? A chemical analysis shall be performed on deposited weld metal for. Small size specimens shall be used only when the material thickness does not permit full size specimens.

In addition, if requested to provide test reports, the manufacturer shall also provide the following, when applicable: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Combining values from the two systems may result in nonconformance with this specification. The testing shall be performed as speci?

These fittings are for use in. The values stated astmm each system may not be exact equivalents; therefore, each system shall be used independently of the other.

Carbon steel WPHY 65 buttweld fittings, ASTM A WPHY GR 65 Pipe Fittings Manufacturer, Exporter.

NDE personnel shall be quali? The chemical composition thus determined. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Only the ultimate tensile strength need meet the minimum requirement of Table 2.

  74LS147 DATASHEET PDF

A860 WPHY 60 PIPE FITTTINGS

JIS G Carbon steel pipes for high pressure service. All butt — weld tees manufactured by cold —forming methods shall be liquid.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are astmm, complete or up to date. Unless the order speci?

ASTM A WPHY GR 60 Pipe Fittings, Carbon steel WPHY 60 buttweld fittings Manufacturer, Exporter.

NDE personal shall be. These fittings are for use in high-pressure gas and oil transmission and distribution systems.

Within the text, the SI units are shown in brackets. These fittings are for use in high-pressure gas and oil transmission and distribution systems. Starting materials shall consist of plate, sheet, forgings, forging quality bar, and seamless or fusion-welded tubular products aztm filler metal added.

Electrodes for the shielded metal-arc process shall be of the low-hydrogen type. The weld metal shall be deposited in accordance with the quali?

iPhone X